adafruit dc & stepper motor hat for raspberry pi – mini kit

24,97 IVA Inclusa

Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. Raspberry Pi and motors are not included. Since the Raspberry Pi does not have a lot of PWM pins, we use a fully-dedicated PWM driver chip onboard to both control motor direction and speed. This chip handles all the motor and speed controls over I2C. Only two pins (SDA & SCL) are required to drive the multiple motors, and since it’s I2C you can also connect any other I2C devices or HATs to the same pins. In fact, you can even stack multiple Motor HATs, up to 32 of them, for controlling up to 64 stepper motors or 128 DC motors (or a mix of the two) – just remember to purchase and solder in a stacking header instead of the one we include. Motors are controlled by TB6612 MOSFET drivers with 1.2A per channel and 3A peak current capability, a big improvement over L293D drivers and there are built-in flyback diodes as well. We even had a little space so we added a polarity protection FET on the power pins and a bit of prototyping area. And the HAT is assembled and tested here at Adafruit so all you have to do is solder on the included 2×20 plain header and the terminal blocks. Lets check out these specs again: 4 H-Bridges: TB6612 chipset provides 1.2A per bridge (3A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 13.5VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution) Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping. Big terminal block connectors to easily hook up wires (18-26AWG) and power Polarity protected 2-pin terminal block and jumper to connect external 5-12VDC power Works best with Raspberry Pi model A+, B+, or Pi 2, but

23,50€
disponibile
2 new from 23,50€
as of 24 Luglio 2024 15:37
Amazon.it
32,42€
disponibile
3 new from 24,09€
as of 24 Luglio 2024 15:37
Amazon.it
33,50€
disponibile
2 new from 33,50€
as of 24 Luglio 2024 15:37
Amazon.it
34,95€
disponibile
2 new from 34,92€
as of 24 Luglio 2024 15:37
Amazon.it
35,49€
disponibile
3 new from 33,95€
as of 24 Luglio 2024 15:37
Amazon.it
35,56€
disponibile
3 new from 31,09€
as of 24 Luglio 2024 15:37
Amazon.it

Informazioni aggiuntive

Binding

Package Quantity

1

UPC

Title

Adafruit DC Stepper Motor HAT for Raspberry Pi – Mini Kit

Studio

Publisher

Product Type Name

Product Group

Part Number

Package Dimensions

Height: 79, Length: 591, Weight: 2, Width: 386

Brand

MPN

Model

2348

Manufacturer

Label

Item Dimensions

Height: 79, Length: 591, Width: 394

EAN List

0748347527568, 3700386523489

EAN

0748347527568

UPC List

UPC List Element: 748347527568

  • Tutti i prezzi elencati qui sopra sono in Euro.
  • This product is available at Amazon.it.
  • Su amazon.it puoi acquistare DC Motor Driver Module HAT For Raspberry Pi Pico Series, Driving Up To 4x DC Motors, I2C controlled, up to 3A Output per solo 16,95€
  • Il prezzo più basso di Adafruit DC e Cofano Motore Passo-Passo per Raspberry Pi è stato trovato su 24 Luglio 2024 15:37.

Adafruit 16-Channel PWM / Servo HAT for Raspberry Pi - Mini Kit

32,42  disponibile
3 new from 24,09€
Spedizione gratuita
Amazon.it
as of 24 Luglio 2024 15:37

Caratteristiche

  • Adafruit 16-Channel PWM / Servo HAT for Raspberry Pi - Mini Kit

Waveshare Motor Driver Hat for Raspberry Pi Onboard PCA9685 TB6612FNG Drive Two DC Motors I2C Interface 5V 3A Can be Stackable up to 32 This Modules

22,15  disponibile
Amazon.it
as of 24 Luglio 2024 15:37

Caratteristiche

  • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards
  • I2C controlled, by setting 5 address jumpers, it is stackable up to 32 this modules; Reserved I2C control pins, allows to work with other control boards
  • Onboard PCA9685 chip, provides 12-bit hardware PWM to adjust motor speed; Onboard TB6612FNG dual H-bridge motor driver, high efficiency, low heating
  • Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminal
  • Comes with development resources and manual (examples in BCM2835, wiringPi, and python), download link: www.waveshare.com/wiki/Motor_Driver_HAT

Waveshare HRB8825 Stepper Motor Hat (B) for Raspberry Pi/Jetson Nano,Drives Two Stepper Motors Up to 1/32 Microstepping, 6 Available Microstepping Modes

23,50  disponibile
2 new from 23,50€
Spedizione gratuita
Amazon.it
as of 24 Luglio 2024 15:37

Caratteristiche

  • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano
  • Onboard dual HR8825 motor controller IC with built-in microstepping indexer, drives two stepper motors, easy to use.6 available microstepping modes, configured with the DIP switches: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
  • Integrates 5V regulator, allows providing power to Raspberry Pi.Onboard multi connector options for stepper motors in different specifications
  • Adjustable motor drive current via potentiometer, maximum 2.5A current output.Protection features: Overcurrent Protection (OCP), Thermal Shutdown (TSD), VM Undervoltage Lockout (UVLO)
  • Provide development resources and manual (examples in BCM2835, wiringPi, and python) in the Wiki :https://www.waveshare.com/wiki/Stepper_Motor_HAT_(B)?Amazon

Adafruit DC e Cofano Motore Passo-Passo per Raspberry Pi

35,56  disponibile
3 new from 31,09€
Spedizione gratuita
Amazon.it
as of 24 Luglio 2024 15:37

Caratteristiche

  • Realizza i tuoi sogni robotici con questo nuovo cofano motore DC + stepper
  • Perfetto per qualsiasi progetto di movimento in quanto può guidare fino a 4 motori CC o 2 motori passo-passo con controllo della velocità PWM completo.
  • Il cappuccio è completamente assemblato e testato, quindi è sufficiente collegarlo direttamente al tuo Raspberry Pi.
  • Installa la libreria Python facile da usare, controlla gli esempi e sei a posto!
  • Funziona meglio con i modelli Raspberry Pi Zero, A +, B + o Pi 2, Pi 3

DC Motor Driver Module HAT For Raspberry Pi Pico Series, Driving Up To 4x DC Motors, I2C controlled, up to 3A Output

16,95  disponibile
Amazon.it
as of 24 Luglio 2024 15:37

Caratteristiche

  • Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series
  • I2C controlled, supports 32x different I2C addresses by setting the 5 address jumpers
  • Onboard PCA9685 chip, provides 12-bit hardware PWM to adjust motor speed
  • Onboard TB6612FNG dual H-bridge motor driver, high efficiency, low heating
  • Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminal; Breakout unused pins of Pico for easy extension

Stepper Motor HAT (B) per Raspberry Pi/Jetson Nano, 2-CH HR8825 Motore Driver Chip Integrato, Guidare due Stepper Motors, fino a 1/32 Micropasso, per Stampanti 3D, Braccio Meccanico ecc.

23,50  disponibile
Amazon.it
as of 24 Luglio 2024 15:37

Caratteristiche

  • HRB8825 Stepper Motor HAT with standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano
  • Onboard dual HR8825 motor controller IC with built-in microstepping indexer, can drive two stepper motors, easy to use
  • 6 available microstepping modes, configured with the DIP switches: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
  • Onboard different stepper motor interfaces, easy access to stepper motors in different specifications
  • Adjustable motor drive current via potentiometer, maximum 2.5A current output, integrates 5V regulator, allows providing power to Raspberry Pi. Protection features: Overcurrent Protection (OCP), Thermal Shutdown (TSD), VM Undervoltage Lockout (UVLO)

AdaFruit MotorShield v2.3 (Assembly Kit) – Motor/Stepper/Servo Shield for Arduino

35,49  disponibile
3 new from 33,95€
Spedizione gratuita
Amazon.it
as of 24 Luglio 2024 15:37

Caratteristiche

Part NumberADA1438
ModelADA1438

Coolwell Waveshare Stepper Motor HAT per Raspberry Pi 4B+4B 3B+3B 2B+Zero W WH Jetson Nano Dual DRV8825 Controller motore fino a 1/32 Microstepping Drive Due motori passo-passo

33,50  disponibile
2 new from 33,50€
Spedizione gratuita
Amazon.it
as of 24 Luglio 2024 15:37

Caratteristiche

  • Il Raspberry Pi motore passo-passo HAT viene fornito con standard Raspberry Pi 40PIN GPIO estensione header, supporta schede serie Raspberry Pi, Jetson Nano
  • La scheda driver del motore passo-passo DRV8825 ha un doppio controller del motore DRV8825 integrato IC con indice microstepping integrato, aziona due motori passo-passo, facile da usare
  • Questo kit di motori passo-passo Raspberry Pi con 6 modalità di microstepping disponibili, configurato con gli interruttori DIP: full-step, half-step, 1/4-step, 1/8-step, 1/16-step e 1/32-step
  • Lo schermo del motore passo-passo Raspberry Pi con corrente di azionamento del motore regolabile tramite potenziometro, potenza di corrente massima 2.5A
  • Non esitate a contattarci se avete qualche problema con l'utilizzo di questo articolo, saremo sempre pronti ad aiutare a risolvere i problemi.

Waveshare Motor Driver Hat for Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+ I2C Interface Drive Two DC Motors DIY Mobile Robots

21,99  disponibile
Amazon.it
as of 24 Luglio 2024 15:37

Caratteristiche

  • The Motor Driver HAT is designed for Raspberry Pi, controlled via I2C interface, will drive two DC motors at the same time. È una scelta ideale per te per robot mobili.
  • Raspberry Pi connettività, compatibile con Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+ I2C controlled, by setting 5 address jumpers, it is stackable up to 32 this module
  • Onboard PCA9685 chip, fornisce 12-bit hardware PWM per regolare la velocità del motore Onboard TB6612FNG dual H-bridge motor driver, alta efficienza, low heating
  • Integrates 5V regolatore, up to 3A output current, can be powered from battery through VIN terminal
  • Riservato I2C control pins, allows to work with other control board Comes with development resources and manual (examples in BCM2835, wiringPi, and piton)

Waveshare Stepper Motor Hat for Raspberry Pi,Jetson Nano Onboard Dual DRV8825 Motor Controller Built-in Microstepping Indexer Drives Two Stepper Motors Up to 1/32 Microstepping

34,95  disponibile
2 new from 34,92€
Amazon.it
as of 24 Luglio 2024 15:37

Caratteristiche

  • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano
  • 6 available microstepping modes, configured with the DIP switches: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step; Adjustable motor drive current via potentiometer, maximum 2.5A current output
  • Protection features: Overcurrent Protection (OCP), Thermal Shutdown (TSD), VM Undervoltage Lockout (UVLO); Integrates 5V regulator, allows providing power to Raspberry Pi
  • Onboard dual DRV8825 motor controller IC with built-in microstepping indexer, drives two stepper motors, easy to use; Onboard multi connector options for stepper motors in different specifications
  • Comes with development resources and manual (examples in BCM2835, wiringPi, and python), download link: www.waveshare.com/wiki/Stepper_Motor_HAT